Bosch PBD 40 Bench Drill – A new and improved press drill

Nice minor drill for common wooden and steel function. After agonizing about no matter if to buy a regular bench drill or this one particular i went a head and purchased a pbd 40 which i use typically to develop situations for prototypes of compact-ish electrical products, antennas and antenna mountings as perfectly as tripod adapters for cameras and other tripod mounted tools. I largely operate with aluminium but also rust cost-free metal. The palms down ideal attribute of this drill is the electronic speed control. The drill has a significant purple swap on the right hand facet that switches between minimal (~200-700 rpm) and significant (~700-2600 rpm) and you can seamlessly raise the rpm to any location you want in people pace ranges. Just past night time i was drilling and countersinking a piece of aluminium. With a regular bench drill like all the other ones i regarded as shopping for this would have involved drilling at substantial rpm, calming the motor spring, unscrewing the locking screw on the leading address off the drill, going rubber belts about to reduce the speed for countersinking, refitting the top rated cover to continue to keep it from rattling about when drilling, re-pressure the motor spring, do the sinks and then reverse the method the following time i want to drill something. With the pbd 40 it is a easy make a difference of turning a couple of knobs. I was not expecting a crazy correct drill in this price tag array but for my functions the pbd 40 is a good deal accurate ample. At to start with i assumed i was detecting some wobble in the drill bit but that turned out to be a bent drill.

I experienced a cheaper drill press from b&q but it just can not drill metal. This bosch is very powerful and steady, with the same drill little bit it can drill by way of 3mm steel with relieve. I set the velocity 850 and it stays steady at 850 in the course of the drilling (the b&q device will often gradual down when drilling). The clamp is also considerably extra handy than the loading plate bundled with the b&q machine.

I made a decision to go for the bosch bench drill for a lot of factors. The principal 1 currently being the wieght of the software, as i have a little workshop and need to have to move equipment on a regular basis. It is extremely light-weight in comparison with most bench drills in this price tag range. It also has the reward of a electronic readout to enable for extremely correct drilling. Far more expensive than numerous of the more classic bench drills on the current market, but truly worth each and every penny.Here are the specifications for the Bosch PBD 40 Bench Drill:

  • Electronic speed adjustment at any time
  • Two-speed gearbox
  • Integrated Laser and PowerLight
  • Digital display for indication the speed
  • Keyless TwinSleeve chuck

A new and improved push drill. Masses of ability for the heavier do the job. Speedy and uncomplicated to set up workpieces. Projected centring cross which is adequate as a speedy tutorial. At this price tag, do not count on ultra precision, but really great plenty of for most domestic positions.

The excellent drill for 21st century woodworkers. The drill forgoes the belts and pullies of old in favour of a contemporary electronic velocity controller that lets the consumer adjust the velocity of the drill as it really is running. There are two gears to swap concerning with the decrease equipment providing higher torque and decreased speeds. Primarily even though i run in the greater gear and have but to locate the drill to struggle with anything. The huge liquid crystal display screen can be toggled between showing drill velocity or depth. It really is vibrant and distinct, and a pretty welcome addition. The laser crosshairs are correct adequate for most needs, but i constantly double verify in advance of drilling by touching the bit versus the workpiece. Even so, i’ve come to count on the crosshairs far far more than i considered i would. The led function light-weight will either be a good help or a pointless gadget depending on how your workshop is lit. For my reasons i find it practical, particularly for highlighting pencil marks on darker woods.

Reviews from purchasers :

  • Quick delivery and machine worked fine for a week then the electronic variable speed control
  • The PBD40 is absolutely perfect for woodwork (and the sort of basic metalwork required
  • Absolutely fine as a drilling machine

Took a minor while to get made use of to digital read out and depth adjustments having said that appears to be to have a good deal of grunt for my do-it-yourself wants. I would recommend you make a decision on the clamp/vice requirements prior to buy. I purchased the bosch clamp attachment. Fast shipping and delivery, no hurt and incredibly content. Update 2 yrs and counting : i have been making use of this bench drill for all of my do it yourself jobs and it has not let me down once. The variable pace command and laser pointer makes it easy to use bore brill bits, counter sinking bits, just about anything you can think of this drill set up is amazing. Each at the time in a even though it is an plan to insert a very little oil to the chuck arrangement. I are unable to fault this drill, one of my ideal buys, happy i did not go for the more cost-effective selection.

Talking only as a woodworker, i have identified this drill preferably suits my prerequisites. It is sturdily developed and worthy of the brand, and i have no concerns with its accuracy or electricity. In reality it is very easily potent and has manufactured easy function of each undertaking i have specified it so much. This is a equipment worthy of looking at for a number of causes, specially if room is restricted. It is gentle ample to be moved about, yet continue to correctly secure. I have hooked up it to a thick plywood foundation, which can be clamped to a bench if necessary (not wanted so considerably). The in-designed clamp is great for rapid get the job done and the detachable fence is perfectly made and secures conveniently to the base. I very considerably like the depth placing element, which enables for repeat holes to be drilled to 1/ten mm precision (i have checked this) and the laser cross-hair is useful for quickly positioning the workpiece (while i prefer to check out the closing place by eye. The pace adjust dial and selector are also good capabilities.

Would favor a lever instead of the wheel feed, but i experience i will get to like it following employing it a bit lengthier. Aside from this small quibble i like the drill incredibly substantially.

Just ideal for the compact workshop. . This is very well built, simple to use and great for the compact workshop wherever area is minimal. I use this for furniture creating in my modest workshop.

Bosch pbd 40 710w bench drill. For starters, and i haven’t still received amazon’s merchandise questionnaire nonetheless – but – when i do they are, regrettably, heading to be hammered for the reason that of. Packaging – doubly so since one more purchaser presently highlighted this and clearly nothing has been completed by amazon to strengthen it . . The unit arrived in the postie’s van in its precise bosch carton, almost nothing else. It experienced had seven bells knocked out of it – holed & rather a great deal slipping aside. No banding tape around it, only the two common narrow nylon straps. It had plainly been opened (for what intent, a single miracles?) at amazon, the three ‘interlocking tabs’ of the carton being rather well diminished to crumpled shreds.

Nice minor drill for common wooden and steel function. After agonizing about no matter if to buy a regular bench drill or this one particular i went a head and purchased a pbd 40 which i use typically to develop situations for prototypes of compact-ish electrical products, antennas and antenna mountings as perfectly as tripod adapters for cameras and other tripod mounted tools. I largely operate with aluminium but also rust cost-free metal. The palms down ideal attribute of this drill is the electronic speed control. The drill has a significant purple swap on the right hand facet that switches between minimal (~200-700 rpm) and significant (~700-2600 rpm) and you can seamlessly raise the rpm to any location you want in people pace ranges. Just past night time i was drilling and countersinking a piece of aluminium. With a regular bench drill like all the other ones i regarded as shopping for this would have involved drilling at substantial rpm, calming the motor spring, unscrewing the locking screw on the leading address off the drill, going rubber belts about to reduce the speed for countersinking, refitting the top rated cover to continue to keep it from rattling about when drilling, re-pressure the motor spring, do the sinks and then reverse the method the following time i want to drill something. With the pbd 40 it is a easy make a difference of turning a couple of knobs. I was not expecting a crazy correct drill in this price tag array but for my functions the pbd 40 is a good deal accurate ample. At to start with i assumed i was detecting some wobble in the drill bit but that turned out to be a bent drill.

Unquestionably fantastic as a drilling machine. I’ve owned and utilized this drill in my gentle steel-performing compact do the job store for 7 months and found it to satisfy all my desires together with precision. The bearings will have settled and operate-in. I’ve just measured the ensuing movement (due to clearance in bearings) at the conclusion of a 13mm drill little bit i. 120mm from the nose of the chuck. The greatest motion checked in all directions on the horizontal aircraft is concerning . Absolutely fantastic as a drilling equipment, some other folks prospects feedback indicate they are hunting for a milling machine – i question how they exactly locate their centre-pop marks and function-piece locating to superior than . I have drilled stainless steel in up to 13mm diameter and with because of ability, treatment and sharp bits, the equipment is quite capable regarding holding the demanded velocity and torques without the need of having difficulties. When new i stripped the equipment-box to review, thoroughly clean and re-grease the bearings and gears and reckoned they were made in good shape-for goal and if wise strip and re-greasing diligence was managed. The electronic depth and velocity indication and illumination are so useful. The laser projected cross-hairs are a tremendous support to home in on centre-marks but they are obviously not not appropriate for centre-popped programs.

I struggled devoid of a drill press for many years and then saw this which at initially sight appeared fairly high-priced. Even so when taking the electrical power, depth of coarseness previously mentioned desk and depth of plunge into account there is absolutely nothing equivalent at any rate i could afford. It was a no-brainer supplied the electronic electric power regulate, digital browse-out and operating clamp. I used it now with a 24 mm forstener little bit in some walnut and it hardly labored up a sweat.

I made a decision to go for the bosch bench drill for a lot of factors. The principal 1 currently being the wieght of the software, as i have a little workshop and need to have to move equipment on a regular basis. It is extremely light-weight in comparison with most bench drills in this price tag range. It also has the reward of a electronic readout to enable for extremely correct drilling. Far more expensive than numerous of the more classic bench drills on the current market, but truly worth each and every penny.

Virtually excellent – it truly is a keeper. . I was incredibly doubtful about this this drill press just after looking at so several adverse stories regarding its ‘wobbly chuck’. It was sent yesterday but i only had a transient time to established up and test it. I ‘found out’ correct absent it couldn’t drill two holes in the similar position just modifying drill sizing and i resolved that the to start with point i’d do today was log on and send out it back. What i actually did to start with was read through the handbook and have a suitable appear at the driller. I located i might not tightened ‘lever 7’ without it there is a lot of perform amongst to motor head and the aid column – – almost nothing to do with the chuck at all. As a result i’m incredibly joyful with it and present my recommendation. (a) do not like the handwheel. (c) the pedestal foundation is a hollow casting so, at the time it is really been bolted to your workbench, the build up of swarf and dust falling as a result of its slots are not able to be cleaned without the need of unbolting it.

Excellent for property wooden functioning. I purchased this to substitute a jet bench major pillar drill principally mainly because my arms are now arthritic. The jet was not the most inexpensive generic pillar drill but this is two times the cost so it wants to be really substantially improved, which for my uses it is. It has been created for diy wooden do the job fairly than getting a bulk typical steel do the job instrument. I want a pillar drill to:*make real ninety diploma holes in wooden *make holes (primarily the larger sized types) without having the wrenching the hand as with a hand held drill*provide depth handle*make occasional holes in metali am delighted due to the fact above the jet the strengths are:*50 % the fat*vastly less complicated velocity modify*vastly easier top change*greater desk* wood to be drilled stays at bench stage*basic workholding for wood as common*laser targetting*solution of superior everlasting worklighti promptly realised the need for a drill vice for larger holes in hardwood. Thake treatment obtaining these as the slots need to have to align.

Took a minor while to get made use of to digital read out and depth adjustments having said that appears to be to have a good deal of grunt for my do-it-yourself wants. I would recommend you make a decision on the clamp/vice requirements prior to buy. I purchased the bosch clamp attachment. Fast shipping and delivery, no hurt and incredibly content. Update 2 yrs and counting : i have been making use of this bench drill for all of my do it yourself jobs and it has not let me down once. The variable pace command and laser pointer makes it easy to use bore brill bits, counter sinking bits, just about anything you can think of this drill set up is amazing. Each at the time in a even though it is an plan to insert a very little oil to the chuck arrangement. I are unable to fault this drill, one of my ideal buys, happy i did not go for the more cost-effective selection.

Brief shipping and equipment labored fantastic for a 7 days then the electronic variable speed handle. Quick supply and equipment worked high-quality for a week then the digital variable velocity control failed to function. Amazon replaced macine very promptly and new device so much operates nicely. It is a quite useful machine for diy get the job done and is exact for this kind of function with extremely tiny wobble. If it in which not for the unlucky failure it would get a 5 star.

A great drill for the beginner. As an amateur woodworker and diy hobbyist this drill satisfies me down to the ground. I can’t reach the pace of drilling holes that i could with my outdated electricity drill in a low cost lever-press, but that might very well be a excellent issue. This just one is precise and safe and sound with the laser crossed-hairs, fence and clampdown. The locking chuck will make it uncomplicated to improve drill bits and there is lots of power to drill deep, clean holes in thick timber with forstner bits. Engineering varieties have dismissed it as an costly electrical power drill on a stand, but owning used these a instrument for yrs i can say that it is a great deal additional than that and, at amazon’s cost, a realistic acquire.

One more terrific bosch equipment to my fleet. This is my to start with bench drill and pretty glad i went for it, no concerns about shifting belts for the velocity given that in this unit anything is control from the panel electronically. Modifying the drill bits quite effortless no keys demanded.I enjoy the clamp which comes really beneficial when i require to maintain my operate piece secured. A bit pricey, hope bosch will make items more cost-effective so we could fill up our workshops with them. So considerably i have made use of only wood and been handling really effectively every little thing so significantly. Not a heavy device but stable (excellent for when not in utilized) just set on the facet and reclaim that area for a further use. Laser is effective great but i constantly verify wherever i want to placement the drill bit 1st. Mild also a reward but no need to have it if you have great illumination at your station.

This factor is incrediblefeatures i love:- slow get started. It starts off gradually and then provides up the pace. In my feeling this is absolutely incredible for some security aspects of a highly effective software like this. I would have expended the added revenue on this tool for this function alone- 750w ability. I’m guaranteed i might be fantastic with less but this is wonderful to have. – not pretty loud, essentially seriously comfortably peaceful at lessen speeds. I like this about a lot of good quality tools from bosch and makita, primarily 18v tools. See under for my sounds measurements. So uncomplicated to dial in precisely what you need from 200 to 2500 rpm. I also really like that the speed is essentially measured by the instrument instead than just displaying a quantity dependent on the posture of the adjustment knob. So for case in point if you might be drilling a difficult product you will see the velocity lessen on the lcd display. – actual physical depth halt and digital depth gauge on the display. – the laser and led gentle are quite nice.

One thought on “Bosch PBD 40 Bench Drill – A new and improved press drill

  1. A very successful modification to eliminate the need for the brake. . As others have said, when unclamped the head is free to move sideways by what must be the best part of a millimetre at the rack. However, when clamped the head is no longer free to move except up and down with the gimmicky handle. On my drill there is minimal sideways chuck movement. The one really horrible thing about my drill was that the adjustable brake (which stops the head dropping if the clamp is released and the handle is unrestrained) juddered considerably regardless of tightness setting and whether the column was dry or lubricated. My modification has completely done away with this. Counterpoising the head allowing the brake to be adjusted so that it has no effect. It so happens that an old sash window weight no. 9kg) that i bought on ebay for £1-50 exactly balances the head of my drill. To stop the roughcast weight rubbing against the back of the drill i have used a length of self-supporting plastic pipe. The only part of the exercise that caused some head scratching was the fixing of the cord to the clamp/brake unit. The fixing had to be as near to the column as possible to reduce any possibility of judder. Visible in the slot between the clamping screw and the grub screw brake adjusters is a plastic tongue, presumably part of the brake lining.
  2. This review is from : Bosch PBD 40 Bench Drill

    A very successful modification to eliminate the need for the brake. . As others have said, when unclamped the head is free to move sideways by what must be the best part of a millimetre at the rack. However, when clamped the head is no longer free to move except up and down with the gimmicky handle. On my drill there is minimal sideways chuck movement. The one really horrible thing about my drill was that the adjustable brake (which stops the head dropping if the clamp is released and the handle is unrestrained) juddered considerably regardless of tightness setting and whether the column was dry or lubricated. My modification has completely done away with this. Counterpoising the head allowing the brake to be adjusted so that it has no effect. It so happens that an old sash window weight no. 9kg) that i bought on ebay for £1-50 exactly balances the head of my drill. To stop the roughcast weight rubbing against the back of the drill i have used a length of self-supporting plastic pipe. The only part of the exercise that caused some head scratching was the fixing of the cord to the clamp/brake unit. The fixing had to be as near to the column as possible to reduce any possibility of judder. Visible in the slot between the clamping screw and the grub screw brake adjusters is a plastic tongue, presumably part of the brake lining.
    1. Quick delivery and machine worked fine for a week then the electronic variable speed control. Quick delivery and machine worked fine for a week then the electronic variable speed control failed to work. Amazon replaced macine very quickly and new machine so far works well. It is a very handy machine for diy work and is accurate for this type of work with very little wobble. If it where not for the unfortunate failure it would get a five star.
      1. Quick delivery and machine worked fine for a week then the electronic variable speed control. Quick delivery and machine worked fine for a week then the electronic variable speed control failed to work. Amazon replaced macine very quickly and new machine so far works well. It is a very handy machine for diy work and is accurate for this type of work with very little wobble. If it where not for the unfortunate failure it would get a five star.
  3. This review is from : Bosch PBD 40 Bench Drill

    A pleasure to use, especially because of the fixed platform and easy height adjustment. I’ve not had this long but so far am very happy with it and agree with most of the other reviews. Mine has a little play in the spindle, not enough to worry about for ordinary wood drilling but i don’t recommend trying to use it for milling or routing or for precision metal work. There are three points that have scarcely if at all been mentioned in other reviews. The first two are why i chose this drill and make it a delight to use (along with the easy speed control, long travel and digital depth gauge):1) the way the platform is fixed and the entire drill head moves up and down the column means that the workpiece is always at the same height no matter what drill bit you are using. So if the workpiece is big enough to need additional support, that support will also always be at the same height. 2) the guide rack on the column means that as you reposition the drill head to suit a longer or shorter bit it doesn’t move from side to side. So if the workpiece is clamped down you can use widely different bits, raising or lowering the drill head as required, without losing the setting. On the first project i used this drill for i had to drill a 4mm hole 80mm deep and then counterbore it 12mm deep. Start with a jobber-length 4mm wood drill, change to a long metal drill to break through, and change again to counterbore.
  4. This review is from : Bosch PBD 40 Bench Drill

    A pleasure to use, especially because of the fixed platform and easy height adjustment. I’ve not had this long but so far am very happy with it and agree with most of the other reviews. Mine has a little play in the spindle, not enough to worry about for ordinary wood drilling but i don’t recommend trying to use it for milling or routing or for precision metal work. There are three points that have scarcely if at all been mentioned in other reviews. The first two are why i chose this drill and make it a delight to use (along with the easy speed control, long travel and digital depth gauge):1) the way the platform is fixed and the entire drill head moves up and down the column means that the workpiece is always at the same height no matter what drill bit you are using. So if the workpiece is big enough to need additional support, that support will also always be at the same height. 2) the guide rack on the column means that as you reposition the drill head to suit a longer or shorter bit it doesn’t move from side to side. So if the workpiece is clamped down you can use widely different bits, raising or lowering the drill head as required, without losing the setting. On the first project i used this drill for i had to drill a 4mm hole 80mm deep and then counterbore it 12mm deep. Start with a jobber-length 4mm wood drill, change to a long metal drill to break through, and change again to counterbore.
    1. Excellent quality and design, near zero chuck wobble as a few have complained. A modern lightweight bench drill well worth the money.
  5. This review is from : Bosch PBD 40 Bench Drill

    Excellent quality and design, near zero chuck wobble as a few have complained. A modern lightweight bench drill well worth the money.
    1. Great for my workshop, use it for wood and metal, i purchased this because it is more compact than most pillar drills, no belts to change for different speeds and torque. Quick to change drill bits, and adjust up/down, depth gauge is good, but depth stop useful for multiple drilling. Unit does have slight play in head/chuck, not enough to put me off, if you use a punch with metal first to centre drill point.
  6. This review is from : Bosch PBD 40 Bench Drill

    Great for my workshop, use it for wood and metal, i purchased this because it is more compact than most pillar drills, no belts to change for different speeds and torque. Quick to change drill bits, and adjust up/down, depth gauge is good, but depth stop useful for multiple drilling. Unit does have slight play in head/chuck, not enough to put me off, if you use a punch with metal first to centre drill point.
    1. This was a bit of extravagance rather than a necessity but had been looking for a second hand pillar drill for a while and nothing was around so took the plunge on this. Constructed a simple wheelie base out of an old cabinet and with it all clamped down it’s pretty good. Smooth adjustment; once you get your head around the depth stops it’s simple to use. Probably a bit underpowered for anything too serious but for your average hobbyist i’ve no doubt it will meet all needs. Rpm readout is fun – if a little pointless. My only criticisms are:1) the wheel on the side to take it up and down. I’d rather it had the typical arm approach – the diameter of the wheel is quite small so for deep cuts it can be a little cumbersome if you need to rotate the wheel a few times. Might try and adapt it somehow. 2) the in built clampy to hold the piece / sacrificial piece in place is a bit of a pain to adjust.
  7. This review is from : Bosch PBD 40 Bench Drill

    This was a bit of extravagance rather than a necessity but had been looking for a second hand pillar drill for a while and nothing was around so took the plunge on this. Constructed a simple wheelie base out of an old cabinet and with it all clamped down it’s pretty good. Smooth adjustment; once you get your head around the depth stops it’s simple to use. Probably a bit underpowered for anything too serious but for your average hobbyist i’ve no doubt it will meet all needs. Rpm readout is fun – if a little pointless. My only criticisms are:1) the wheel on the side to take it up and down. I’d rather it had the typical arm approach – the diameter of the wheel is quite small so for deep cuts it can be a little cumbersome if you need to rotate the wheel a few times. Might try and adapt it somehow. 2) the in built clampy to hold the piece / sacrificial piece in place is a bit of a pain to adjust.
    1. The pbd40 is absolutely perfect for woodwork (and the sort of basic metalwork required. I thoroughly endorse the positive reviews of this product – i haven’t bothered using my ancient quill-based pillar drill since getting it. The pbd40 is absolutely perfect for woodwork (and the sort of basic metalwork required by a woodworker or hobbyist). It isn’t intended as a high-precision engineer’s tool for metal. (pillar drills, of course, aren’t designed for woodwork)tip for those who complain about wood chips getting trapped underneath – fit a couple of 50mm square strips of scantling under the base, one at each side, as a standoff. Then screw a strip of 50 x 25 underneath those across the front so that the whole thing docks neatly with the edge of your workbench. The whole thing is light enough to keep on a shelf or table and move to the bench when needed. The least pleasant feature is that silly hand wheel (though i acknowledge some people may like it) – i’ve drilled the spokes where they join the rim and stuck on three cheap parallel control handles – much nicer to use. I’ve tried the runout of the chuck with a test dial indicator and it’s well within the claimed limits.
      1. The pbd40 is absolutely perfect for woodwork (and the sort of basic metalwork required. I thoroughly endorse the positive reviews of this product – i haven’t bothered using my ancient quill-based pillar drill since getting it. The pbd40 is absolutely perfect for woodwork (and the sort of basic metalwork required by a woodworker or hobbyist). It isn’t intended as a high-precision engineer’s tool for metal. (pillar drills, of course, aren’t designed for woodwork)tip for those who complain about wood chips getting trapped underneath – fit a couple of 50mm square strips of scantling under the base, one at each side, as a standoff. Then screw a strip of 50 x 25 underneath those across the front so that the whole thing docks neatly with the edge of your workbench. The whole thing is light enough to keep on a shelf or table and move to the bench when needed. The least pleasant feature is that silly hand wheel (though i acknowledge some people may like it) – i’ve drilled the spokes where they join the rim and stuck on three cheap parallel control handles – much nicer to use. I’ve tried the runout of the chuck with a test dial indicator and it’s well within the claimed limits.
  8. This review is from : Bosch PBD 40 Bench Drill

    Another great bosch machine to my fleet. This is my first bench drill and very glad i went for it, no worries about changing belts for the speed since in this unit everything is control from the panel electronically. Changing the drill bits very easy no keys required.I love the clamp which comes very useful when i need to keep my work piece secured. A bit pricey, hope bosch will make items more affordable so we could fill up our workshops with them. So far i have used only wood and been handling very well everything so far. Not a heavy machine but solid (perfect for when not in used) just put on the side and reclaim that space for another use. Laser works great but i always check where i want to position the drill bit first. Light also a bonus but no need it if you have good illumination at your station.
  9. This review is from : Bosch PBD 40 Bench Drill

    Another great bosch machine to my fleet. This is my first bench drill and very glad i went for it, no worries about changing belts for the speed since in this unit everything is control from the panel electronically. Changing the drill bits very easy no keys required.I love the clamp which comes very useful when i need to keep my work piece secured. A bit pricey, hope bosch will make items more affordable so we could fill up our workshops with them. So far i have used only wood and been handling very well everything so far. Not a heavy machine but solid (perfect for when not in used) just put on the side and reclaim that space for another use. Laser works great but i always check where i want to position the drill bit first. Light also a bonus but no need it if you have good illumination at your station.
    1. This thing is incrediblefeatures i love:- slow start. It starts slowly and then brings up the speed. In my opinion this is absolutely amazing for some safety aspects of a powerful tool like this. I would have spent the extra money on this tool for this feature alone- 750w power. I’m sure i’d be fine with less but this is nice to have. – not very loud, actually really comfortably quiet at lower speeds. I love this about many quality tools from bosch and makita, especially 18v tools. See below for my noise measurements. So easy to dial in exactly what you need from 200 to 2500 rpm. I also love that the speed is actually measured by the tool rather than just showing a number based on the position of the adjustment knob. So for example if you’re drilling a tough material you will see the speed decrease on the lcd screen. – physical depth stop and digital depth gauge on the screen. – the laser and led light are very nice.
  10. This review is from : Bosch PBD 40 Bench Drill

    This thing is incrediblefeatures i love:- slow start. It starts slowly and then brings up the speed. In my opinion this is absolutely amazing for some safety aspects of a powerful tool like this. I would have spent the extra money on this tool for this feature alone- 750w power. I’m sure i’d be fine with less but this is nice to have. – not very loud, actually really comfortably quiet at lower speeds. I love this about many quality tools from bosch and makita, especially 18v tools. See below for my noise measurements. So easy to dial in exactly what you need from 200 to 2500 rpm. I also love that the speed is actually measured by the tool rather than just showing a number based on the position of the adjustment knob. So for example if you’re drilling a tough material you will see the speed decrease on the lcd screen. – physical depth stop and digital depth gauge on the screen. – the laser and led light are very nice.
  11. This review is from : Bosch PBD 40 Bench Drill

    What a fantastic piece of kit i’m running out of things to drill holes in.
  12. Brilliant for home wood working. I bought this to replace a jet bench top pillar drill primarily because my hands are now arthritic. The jet was not the cheapest generic pillar drill but this is twice the price so it needs to be very much better, which for my purposes it is. It has been designed for diy wood work rather than being a bulk standard metal work tool. I want a pillar drill to:*make true 90 degree holes in wood *make holes (especially the larger ones) without the wrenching the hand as with a hand held drill*provide depth control*make occasional holes in metali am delighted because over the jet the advantages are:*half the weight*vastly easier speed change*vastly easier height change*larger table* wood to be drilled stays at bench level*basic workholding for wood as standard*laser targetting*option of good permanent worklighti quickly realised the need for a drill vice for larger holes in hardwood. Thake care buying these as the slots need to align.
    1. Brilliant for home wood working. I bought this to replace a jet bench top pillar drill primarily because my hands are now arthritic. The jet was not the cheapest generic pillar drill but this is twice the price so it needs to be very much better, which for my purposes it is. It has been designed for diy wood work rather than being a bulk standard metal work tool. I want a pillar drill to:*make true 90 degree holes in wood *make holes (especially the larger ones) without the wrenching the hand as with a hand held drill*provide depth control*make occasional holes in metali am delighted because over the jet the advantages are:*half the weight*vastly easier speed change*vastly easier height change*larger table* wood to be drilled stays at bench level*basic workholding for wood as standard*laser targetting*option of good permanent worklighti quickly realised the need for a drill vice for larger holes in hardwood. Thake care buying these as the slots need to align.
  13. This review is from : Bosch PBD 40 Bench Drill

    The ideal drill for 21st century woodworkers. The drill forgoes the belts and pullies of old in favour of a modern electronic speed controller that lets the user adjust the speed of the drill as it’s running. There are two gears to switch between with the lower gear providing higher torque and lower speeds. Mostly though i run in the higher gear and have yet to find the drill to struggle with anything. The large lcd display can be toggled between showing drill speed or depth. It’s bright and clear, and a very welcome addition. The laser crosshairs are accurate enough for most purposes, but i always double check before drilling by touching the bit against the workpiece. Even so, i’ve come to rely on the crosshairs far more than i thought i would. The led work light will either be a great aid or a pointless gadget depending on how your workshop is lit. For my purposes i find it useful, especially for highlighting pencil marks on darker woods.
  14. This review is from : Bosch PBD 40 Bench Drill

    The ideal drill for 21st century woodworkers. The drill forgoes the belts and pullies of old in favour of a modern electronic speed controller that lets the user adjust the speed of the drill as it’s running. There are two gears to switch between with the lower gear providing higher torque and lower speeds. Mostly though i run in the higher gear and have yet to find the drill to struggle with anything. The large lcd display can be toggled between showing drill speed or depth. It’s bright and clear, and a very welcome addition. The laser crosshairs are accurate enough for most purposes, but i always double check before drilling by touching the bit against the workpiece. Even so, i’ve come to rely on the crosshairs far more than i thought i would. The led work light will either be a great aid or a pointless gadget depending on how your workshop is lit. For my purposes i find it useful, especially for highlighting pencil marks on darker woods.

Comments are closed.